I’d stop using the clonex spray @xgx13xgx. I was looking into that product recently and there is no need for it. We’ve all been taking and growing successful clones for years without that type of product. A dip in clonex gel, and running clonex solution for initial rooting works great. Just mist your dome and that’s enough.
They just had to make another product to market to use for their financial gain. That stuff is a waste of money 
!
2 Likes
I stopped using the clonex spray it was just the bottle of clonex solution mixed with water I’m not using a dome dude I hope this isnt PM never had it dont want it
2 Likes
I say they’re looking ok. I can see that white on the very tips. Have you tried to rinse that with ro or distilled h20? If it’s residue from your spray it’ll come right off.
I had a little bit of PM from a clone run from overspraying my clones with H20. I just removed the leaves that had it. You’ll have plenty of new growth soon.
1 Like
I’ll never make that mistake again. If you haven’t been using a dome I doubt it is PM my friend.
2 Likes
These dont even have roots I just sprayed with h20 and wiped when it dries I’ll be able to tell if its residue I hope so if not I’ll cut the leaves out they dont have roots yet still rough like sand paper so hopefully in the next 3 to 5 days roots will come in
3 Likes
They look fine. Let them be. I’ve had leaves in worse condition. Mold and mildew come from humidity. Stop spraying and take the dome off a little bit more each time.
2 Likes
Not using a dome but I will stop spraying I was able to wipe the powder off I am not running these this next run I have some critical mass collective alien masster kush and purple skunk mass but the strains I ha e especially the HSO amhurst sour diesel are amazing and have to keep for later
4 Likes
So I just cut off the bad leaves one of the stems is white and flimsy so I’m guessing it’s gone the others seem ok they have had light 24 7 for a week should I switch the light cycle
2 Likes
I don’t run a dome at all on mine. Cut stem at a 45 and make a couple little cuts at the bottom. Dip in clone x hell then Full strength clone x nutes and I added root excelerator this time.
Keep your water at 5.8 ph and 78 degrees and give them time!
But ya no dome on spray cloners. That’s what I’ve been told and what I’ve done the last couple runs
Also I keep a very dim t5 or led light about 4-6 inches away. Keep the light and pumps on 24/7
2 Likes
Nice i haven’t tried it.
2 Likes
I agree with this. I don’t spray clones. My first time using cloner made cloning too easy actually. you don’t have to do much really unless your trying to speed up process. Cutting at a angle as you take off clones and putting in water immediately then dip in cloning gel let sit for a min or so then into cloner with cloning solution in reservoir would do the job. No spray needed on plants. Spray tent with reg water to keep humidity up. Keep temp anywhere from 73-79F and wait.
Cutting/shaving stem at 45 degree angle with clean razor and cutting tips of leaves work also. But I found out they are not necessary for roots to grow. And I haven’t did a test to see if it makes it faster yet. One more thing I found that the bigger clones root faster and they grow faster. The clones closest to the sprayer in reservoir root faster at least in my cloner.
3 Likes
And I just put mine in a jar of water after the 45 cut, some removal of green at bottom and root hormone, and then change the water out each day until roots. Lol. Poor man’s method.
1 Like
I cut leaves for extra space and better air flow but you’re right these aeroponic cloners make things too easy lol
2 Likes
Yes, you only need a timer
Thats all
I set my timer 15min on and 45min off and repeat